Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Crown Heights Homeowners
A missing or cracked chimney cap and crown are the two most common reasons water gets into a Crown Heights chimney. The cap keeps rain, birds, and squirrels out of the flue; the crown, the concrete slab at the top of the masonry, sheds water away from the brick below it. When either one fails, water works its way into the chimney structure and shows up as ceiling stains, spalling brick, or rusted damper hardware. Our technicians have up to 10 years of experience with exactly this kind of work, and we handle cap installation, crown repair, and crown coating in a single visit. For a free estimate, call (833) 858-5823. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

What Our Chimney Cap & Crown Service Includes
Caps and crowns are the first line of defense for a chimney, and each one needs a different approach. Here’s what we do for each.
Cap Installation
A chimney cap is a metal or mesh cover that sits on top of the flue and keeps rain, snow, animals, and debris from falling into the chimney. You need one if your flue is open to the sky, if you’re hearing scratching or chirping from the chimney, or if water is pooling in the firebox after a storm. We measure the flue opening, fit a cap sized to the actual crown, and anchor it so it holds in wind without cracking the masonry below.
Cap Replacement
Chimney caps rust through, lose their screens to storms, or get bent by falling branches. A replacement is needed when the existing cap no longer seals the flue or when the screen has gaps that let animals in. We remove the old cap, check the flue tile and crown for damage underneath, then install a new cap built for the flue size. Leaving a damaged cap in place is how a small problem turns into water damage you can’t see.
Crown Repair
The crown is the sloped concrete or mortar surface at the top of the chimney that pushes water away from the brick. Hairline cracks, chunks missing from the edge, or a crown that has pulled away from the flue tile all mean water is getting inside the masonry. We repair cracks and rebuild damaged sections using a crown mix that matches the existing masonry. A crown that’s too far gone gets replaced rather than patched.
Crown Coating
Crown coating is a flexible sealant applied over a crown that’s sound but showing surface wear. It’s the right call when the crown isn’t crumbling yet but has small cracks that will open up over another heating season. We clean and prep the surface first, then apply a coating designed to move with the masonry instead of cracking off in the cold. Coating a crown that’s already failing just hides the problem, so we inspect before we recommend it.
Multi-Flue Cap
A multi-flue cap covers two or more flue openings under a single top plate. Crown Heights homes with an original fireplace plus a furnace flue often have two openings close together, and a single cap protects both. We build the cap to fit the exact footprint of the crown, with individual screens sized to each flue. It’s a cleaner setup than two separate caps fighting for the same space.
Custom Cap
Some chimneys have odd shapes, oversize flues, or crown dimensions that don’t match stock sizes. A custom cap is fabricated to fit the opening exactly, which matters for wind resistance and for keeping water out at the edges. We measure on site and have the cap built to those measurements. It costs more than a stock cap, but a loose cap that doesn’t sit right is worse than no cap at all.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with caps and crown materials from brands we know well. Olympia Chimney makes caps and top-sealing dampers used widely across New York, and we’ve fitted enough of them to know where the mounting hardware wears and how to size the screens correctly. Gelco is another line we see regularly on Crown Heights chimneys, particularly on older masonry crowns where a proper crown mix matters.
Famco caps come up too, often on homes where a previous owner had work done. We know their dimensions and mounting style, so replacing one is a straightforward job rather than a puzzle. Whether you have Olympia Chimney, Gelco, Famco, or any other make, we can help. We don’t claim to be a dealer for any of these lines; we just know how they’re built and how to install and repair them properly. For flue repair underneath a damaged crown, we use HeatShield ceramic systems, which are engineered for the flue environment rather than borrowed from general masonry work.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. If you’re finding damp ash, a puddle, or rust on the damper after a storm, the cap is missing, damaged, or the crown is funneling water into the flue. This is the clearest sign that something at the top of the chimney needs attention.
- Brick spalling or white staining on the chimney exterior. Flaking brick faces and white mineral deposits on the outside of the chimney usually mean moisture is getting in from above and pushing out through the masonry. A failed crown is a common cause.
- Animals or nesting material in the flue. Birds, squirrels, and raccoons get into uncapped chimneys regularly, and nesting material is a fire hazard once you light a fire. A proper cap with intact screening closes that door.
- A visibly cracked or crumbling crown. If you can see cracks from the ground, or chunks of concrete on the roof or in the yard, the crown is failing. Small cracks widen through freeze-thaw cycles and let water into the chimney structure.
- The cap is loose, rusted, or missing screens. A cap that shifts in the wind or has torn screens isn’t doing its job. Loose caps can also damage the flue tile as they move.
Our Chimney Cap & Crown Process – Step by Step
- 1
Phone call and scheduling. You call (833) 858-5823, tell us what you’re seeing, and we book a visit. We answer 24/7, and dispatch runs 7am to 7pm, Sunday through Friday. If you’re dealing with an active leak, we’ll ask enough questions to understand the urgency before we arrive.
- 2
On-site inspection. We look at the cap, the crown, the flue tile, and the masonry below the crown line. Where it helps, we use a camera to check the flue from the inside. You get a plain explanation of what we found, not a sales pitch.
- 3
Written estimate. Every job gets a written estimate before any work starts. The estimate itemizes the cap or crown work and any related repair we recommend. If something can safely wait, we’ll tell you that too.
- 4
Installation or repair. We install the cap, rebuild or coat the crown, or repair the masonry as agreed. Materials are chosen for chimney work specifically, including HeatShield for flue resurfacing where the crown damage has affected the flue.
- 5
Final check and cleanup. We confirm the cap is secure, the crown sheds water the way it should, and the work area is clean. You get a chance to look at the finished job before we pack up.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Crown Heights?
Most chimney cap and crown work in Crown Heights falls into a predictable range, and a written estimate confirms the final price before anything starts. A typical cap installation runs $250 – $550 depending on flue size and cap type. Cap replacement is usually $200 – $450. Crown repair generally runs $350 – $800 depending on how much of the crown needs rebuilding. Crown coating is typically $300 – $600. Multi-flue caps and custom caps run higher, often $500 – $1,000 or more, because they’re built to fit.

Several things move the price. The height and pitch of the roof affect how long the job takes. The condition of the flue tile underneath matters too: if the crown has been failing for a while, water may have damaged the flue, which adds repair cost. Access matters as well. A chimney on a steep roof or behind a dormer takes longer to reach safely.
To avoid overpaying, ask for the estimate in writing and make sure it separates the cap or crown work from any flue repair. A free estimate should include a look at the cap, crown, and flue, a clear recommendation, and a price. If a contractor won’t put it in writing, walk away. For an exact quote on your chimney, call (833) 858-5823. Estimates are free.
Chimney Cap & Crown Near Crown Heights – Our Service Area
We work across Crown Heights and the surrounding neighborhoods, including East Flatbush, Prospect Heights, Bedford-Stuyvesant, Flatbush, Brownsville, Clinton Hill, Park Slope, Fort Greene, Kensington, and Bushwick. If you’re in one of these areas and need a cap or crown looked at, call and we’ll book you in. You can also read more about our chimney sweep in Crown Heights if you’re due for a cleaning alongside the repair. For nearby neighborhoods, see our chimney cap & crown in East Flatbush and chimney cap & crown in Williamsburg pages.
Serving Crown Heights, NY – Our Local Coverage Area
We serve Crown Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Crown Heights
Chimney cap and crown work covers the two protective parts at the top of your chimney. The cap is the cover that keeps rain, animals, and debris out of the flue, and the crown is the sloped concrete surface that sheds water away from the brick. Together they keep moisture out of the chimney structure. When either one fails, water gets in and damages the masonry, flue, and damper.
Most cap installations and crown repairs are completed in a single visit, usually a few hours depending on roof access and the extent of the damage. A straightforward cap replacement is quicker than a crown rebuild. Custom caps take longer because they’re fabricated to measure, so there’s a lead time before installation. We’ll give you a realistic timeline with the estimate.
Cap installation typically runs $250 – $550, cap replacement $200 – $450, crown repair $350 – $800, and crown coating $300 – $600. Multi-flue and custom caps usually run $500 – $1,000 or more. The written estimate sets the final price based on your chimney’s condition and roof access. Call (833) 858-5823 for an exact quote; estimates are free.
Yes. We service Olympia Chimney, Gelco, Famco, and other cap and crown brands, and we know how each one is built and mounted. That matters most on replacements, where the new cap has to fit the existing crown and flue correctly. Whether you have a brand we’ve named or another make, we can help.
Same-day service is available depending on the schedule. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. We’re closed Saturday. Call (833) 858-5823 to book.
Our workmanship is covered, and the terms are spelled out in the written estimate so you know what’s covered before we start. Material warranties depend on the brand of cap or crown product used, and we’ll explain those terms at the estimate stage. If something looks off after the work is done, call us and we’ll take a look.
Clear access to the fireplace and the roof if possible, and let us know about any pets or gate codes. If you’ve noticed water in the firebox or a specific leak, have those details ready. There’s nothing else you need to do. We handle the roof access and the inspection, and we’ll walk you through what we find. For the related service that pairs well with cap work, see our chimney inspection page, or read about chimney repair if the masonry has already taken on water.
Schedule Your Chimney Cap & Crown Service in Crown Heights Today
If your cap is missing, rusted, or your crown is cracked, the sooner it’s handled the less chance water gets into the chimney structure. Call (833) 858-5823 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 10 years of experience, and every job gets a written estimate before work starts. Fireplace repair, sweep, and inspection work are handled by the same company, so there’s no second contractor to call.
Written by the team at Chimney Sweep Crown Heights.