Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Crown Heights Homeowners
Crown Heights has a lot of aging masonry chimneys, and the freeze-thaw cycles that roll through here every winter work on them year after year. Mortar joints crack, bricks spall, and water finds its way into places you can’t see from the sidewalk. When that happens, a small repair becomes a big one fast. Our technicians have up to 10 years of experience diagnosing exactly this kind of damage, and we handle the whole system: sweep, inspect, repair, and upgrade. We connect you with a local pro who’s licensed and insured as their state requires, and every repair starts with camera evidence you can see for yourself. Call (833) 858-5823 and we’ll book you a chimney repair visit in Crown Heights.

What Our Chimney Repair Service Includes
Chimney repair isn’t one job. It’s a set of distinct fixes, and the right one depends on what the inspection turns up. Here’s what we handle in Crown Heights, and what each one actually means for your chimney.
Mortar Repointing
Repointing is replacing the worn mortar between bricks, not the bricks themselves. You need it when the joints have receded or turned crumbly and the brickwork starts looking like stacked blocks with gaps. We grind out the old mortar to the right depth and pack in fresh mortar matched to the original, so the repair holds through Crown Heights winters instead of flaking off by spring.
Spalling Brick Repair
Spalling is when the face of a brick peels, flakes, or pops off, usually because moisture got in and froze. You’ll spot it as brick dust on the roof or pile of red flakes at the base of the chimney. We replace the damaged bricks rather than patching over them, because a spalled brick left in place keeps absorbing water and pushes the damage into the next course.
Chimney Waterproofing
Waterproofing is a breathable sealer applied to the exterior masonry to keep rain out while letting moisture inside escape. You need it after a repair, or on any older chimney that’s absorbing water like a sponge. We apply vapor-permeable sealant so the brick can dry, which prevents the freeze-thaw damage that causes spalling and cracked mortar in the first place. It’s one of the simplest ways to protect an aging Crown Heights chimney.
Flashing Repair
Flashing is the metal where the chimney meets the roof, and it’s the most common source of chimney leaks. You need it when you see water stains on the ceiling or attic sheathing near the chimney, or when the metal has pulled away from the masonry. We reseal or replace the flashing with a proper counter-flashing and cap system, tied into the roof so water runs off instead of running in.
Chimney Rebuilding
Rebuilding is for chimneys where the top courses are too far gone for spot repairs. It’s usually the upper section above the roofline, where weather hits hardest. We tear down the failed masonry to sound brick, rebuild with new brick and mortar, and finish with a proper crown so the new work lasts. Structural work like this is a trained-professional job: it involves height work and the chimney’s structural integrity, so don’t attempt it yourself.
Tuckpointing
Tuckpointing is the finer version of repointing: filling the joints with mortar and then adding a raised, shaped finish for a cleaner, more uniform look. You need it when the masonry is structurally sound but the joints look rough and uneven. We match the finish to the surrounding brickwork so the repair blends in rather than standing out. It’s a detail that matters on a visible Crown Heights chimney.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with materials from a vetted roster of professional-grade brands, the same lines certified chimney professionals use nationwide. HeatShield ceramic repair systems are engineered specifically for flue interiors, and we use them to resurface deteriorated masonry flues rather than tearing the whole chimney apart. Gelco products are built for the masonry side of chimney repair, and we rely on them when sealing and protecting brickwork in this climate. Olympia Chimney supplies components for the kind of structural and cap work we do, and we’ve learned where each one is the right choice and where it isn’t.
Famco is another brand we know inside and out, particularly for the parts and materials that keep a repair holding over time. Knowing a product’s failure points matters as much as knowing how to install it, and that’s what tells us whether a repair will last through the next few winters. Whether you have HeatShield, Gelco, Olympia Chimney, Famco, or any other make, we can help.
Signs You Need Chimney Repair Right Now
Most chimney damage gives you warning signs before it becomes a real problem. Here’s what to look for, and why each one matters.
- Crumbling mortar in the joints. If the mortar between bricks is receding, sandy, or falling out, the brickwork is losing its structural bond. Small joint failures widen fast once water gets behind them, so this is one to catch early.
- Flaking brick or brick dust. Spalling brick means moisture has already penetrated the masonry and is freezing inside it. Left alone, the damage spreads course by course, and what starts as a surface fix can turn into a rebuild.
- Water stains near the chimney. Brown rings on ceilings or attic sheathing point to flashing or crown failure. Water tracking into the house can damage framing and insulation long before you notice the ceiling, so it’s worth a look sooner rather than later.
- White staining on the exterior brick. That chalky white powder is efflorescence, a sign the masonry is pulling moisture through. It often shows up before visible cracking, and it tells you waterproofing is needed.
- A leaning or visibly damaged chimney. A chimney that leans, has cracked courses, or lost bricks is a structural issue, not a cosmetic one. Stop using the fireplace and have it inspected before any more burning, because a compromised chimney can let smoke and carbon monoxide into the living space.
Our Chimney Repair Process – Step by Step
Every repair starts with the same thing: understanding what’s actually wrong before we touch anything.

- 1
Inspection first. We do a Level 1 or Level 2 inspection aligned with NFPA 211 standards, depending on what your situation calls for. A Level 2 inspection includes a camera scan of the flue, which is the only way to see what’s happening inside the chimney.
- 2
Camera evidence and a photo report. Nothing gets recommended without video you can look at yourself. We show you the flue interior on camera and give you a photo report, so you can see the crack or the failing joint rather than take our word for it.
- 3
A written estimate. We walk you through what needs fixing, what can safely wait, and what it will cost. The price is set per job by the written estimate, agreed before the work is booked.
- 4
The repair. We do the work with materials chosen for flue and masonry environments: HeatShield for flue resurfacing, DuraFlex flexible liner systems for relining, and matched mortar and brick for the exterior. Common repairs like cap, crown, and flashing work are handled by the same specialist, so there’s no second contractor.
- 5
A final check and a walkthrough. We confirm the repair is sound and show you the result. If anything else needs attention down the line, you’ll know about it now, not after a leak shows up.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Crown Heights?
Chimney repair in Crown Heights typically runs from a few hundred dollars for a targeted fix to several thousand for a rebuild, depending on which part of the chimney has failed and how far the damage has spread. Here’s a rough picture of common scenarios, though your written estimate sets the final price.
- Mortar repointing or tuckpointing: typically $350-$900, depending on how many joints are involved and how high up the work goes.
- Flashing repair: typically $300-$700, driven by roof access and whether the flashing can be resealed or needs replacing.
- Chimney waterproofing: typically $250-$600, based on the size of the exposed masonry.
- Spalling brick repair: typically $500-$1,500, depending on how many bricks need replacement.
- Chimney rebuilding: typically $2,500-$8,000 or more, based on the height of the section being rebuilt and access to the roof.
What moves the price most is access and extent: a repair at the roofline costs more than one at eye level, and a problem caught early costs less than one that’s spread. The way to avoid overpaying is to get the inspection and the camera evidence first, so you’re fixing what’s actually wrong rather than guessing. Our estimates are free, and we’ll tell you plainly when work can safely wait.
Chimney Repair Near Crown Heights – Our Service Area
We connect homeowners across the Crown Heights area with independent local chimney professionals, including East Flatbush, Prospect Heights, Bedford-Stuyvesant, Flatbush, Brownsville, Clinton Hill, and Park Slope. If your chimney is showing signs of damage, we can also help with chimney repair in nearby East Flatbush and chimney repair in Williamsburg. Call (833) 858-5823 to book a visit. We answer 24/7.
Serving Crown Heights, NY – Our Local Coverage Area
We serve Crown Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Crown Heights
Chimney repair is fixing the parts of the chimney that have failed or worn out: mortar joints, bricks, flashing, the crown, or the flue liner itself. It’s different from a sweep, which cleans the flue, and from an inspection, which finds the problems in the first place. In practice, most repairs in Crown Heights start with an inspection that shows what’s actually damaged. Call (833) 858-5823 to book one.
Most chimney repairs take a few hours to a day, though a full rebuild can run several days depending on the size of the section and the weather. Small jobs like repointing or flashing repair are often done in a single visit. Larger structural work needs more time, and we’ll give you a realistic timeline in the written estimate before anything is booked. Call (833) 858-5823 for an exact quote – estimates are free.
Typical chimney repair in Crown Heights ranges from about $250-$600 for waterproofing up to $2,500-$8,000 or more for a rebuild, with most targeted repairs falling in the $300-$1,500 range. The final price depends on what’s damaged, how high up it is, and how far the problem has spread. The written estimate sets the final price, and it’s agreed before the work is booked. Call (833) 858-5823 for an exact quote – estimates are free.
Yes. We work with HeatShield ceramic repair systems for flue resurfacing and DuraFlex flexible liner systems for relining, along with Gelco, Olympia Chimney, and Famco on the masonry and structural side. These are professional-grade materials engineered for flue environments, and we choose them because they hold up in this climate. Whether your chimney already has one of these systems or needs one installed, we can help. Call (833) 858-5823.
Same-day visits are often possible when you call early. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening. Call (833) 858-5823 to check availability.
Our work comes with a satisfaction guarantee, and the local pro you’re connected with stands behind the repair. The specifics depend on the type of work, so we spell them out in the written estimate before the job starts. If something isn’t right after a repair, call us and we’ll take a look. Call (833) 858-5823 with any questions.
Clear the area around the fireplace and the hearth, and make sure we can get to the roof access if the repair involves exterior work. If you’ve noticed leaks, staining, or debris, jot down where and when you saw it, since that helps us target the inspection. You don’t need to do anything else; the inspection and camera scan come first. Call (833) 858-5823 to schedule.
Schedule Your Chimney Repair Service in Crown Heights Today
If your chimney is showing cracked mortar, spalling brick, or a leak you can’t trace, don’t wait for the next freeze to make it worse. One specialist handles the full system, from the sweep and the inspection through the repair and the upgrade, using professional-grade materials built for flues. Call (833) 858-5823 for a no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You can also start with a chimney sweep Crown Heights and let the inspection tell you what’s needed.
Written by the team at Chimney Sweep Crown Heights.